Upgrading to Super Z II - What do I need exactly?

A place to get answers about which CNC products to look at for your specific application. We have everything from complete controllers in different sizes and in both stepper and servo configurations. A good place to start and get basic answers
Post Reply
User avatar
txtrone
Posts: 40
Joined: Sat Oct 20, 2018 3:13 pm
Location: Fort Worth, TX

Upgrading to Super Z II - What do I need exactly?

Post by txtrone » Sat Sep 12, 2020 10:51 am

Back in June of 2018 I purchased the BladeRunner Dragon Cut 300-4 Bundle w/ MIC 01 connection
cable + Feather Touch and also the HyT Connect RS485 SIM Kit B (without Hub).

I am now in the process of upgrading to my second table and would like to add the Super Z II. I contacted CandCNC before placing the order of the SuperZ, per the instructions on the website. David was helpful and told me I would need to get the "12.6 Table I/O as well". After adding the cable length for my 5x10 table as well as the magnetic breakaway mount, the total came up to $875. I asked if he could send me a PayPal invoice and he agreed, but it never came through. I don't mind adding the items to my basket and checking out, but I can't find the "12.6 Table I/O".
Precision Plasma Magnum 7 HD on a five by ten
CommandCNC Linux
Hypertherm Powermax 85

When all else fails... read the directions.

admin13o5
Site Admin
Posts: 5058
Joined: Tue Sep 03, 2013 5:39 pm

Re: Upgrading to Super Z II - What do I need exactly?

Post by admin13o5 » Sat Sep 12, 2020 1:51 pm

I just added the table i/o 12.6 to the Replacement Parts section .

User avatar
txtrone
Posts: 40
Joined: Sat Oct 20, 2018 3:13 pm
Location: Fort Worth, TX

Re: Upgrading to Super Z II - What do I need exactly?

Post by txtrone » Sat Sep 12, 2020 4:51 pm

Thanks! I just placed my order.
Precision Plasma Magnum 7 HD on a five by ten
CommandCNC Linux
Hypertherm Powermax 85

When all else fails... read the directions.

admin13o5
Site Admin
Posts: 5058
Joined: Tue Sep 03, 2013 5:39 pm

Re: Upgrading to Super Z II - What do I need exactly?

Post by admin13o5 » Sat Sep 12, 2020 10:20 pm

Thsnks!

User avatar
txtrone
Posts: 40
Joined: Sat Oct 20, 2018 3:13 pm
Location: Fort Worth, TX

Re: Upgrading to Super Z II - What do I need exactly?

Post by txtrone » Sun Sep 13, 2020 8:10 pm

admin13o5 wrote:
Sat Sep 12, 2020 10:20 pm
Thsnks!
I nearly bought a few more accessories, but one thing at a time for me! I got the motors today and tested/labeled them before installing them on the new table. Thank you for the instructions on adjusting the gecko drivers!
Precision Plasma Magnum 7 HD on a five by ten
CommandCNC Linux
Hypertherm Powermax 85

When all else fails... read the directions.

davidwoods
Posts: 12
Joined: Wed Aug 15, 2018 12:53 pm

Re: Upgrading to Super Z II - What do I need exactly?

Post by davidwoods » Mon Sep 21, 2020 11:26 am

I am not for sure why you did not get your pp invoice, I am sorry(I can not see who you are on here). Did you end up getting another 12v wall plug, with the 12.6 IO? If your breakout board is UBOB, you will need a second one to power the FT-02 module. Please call me at CandCNC, if you did not.

User avatar
txtrone
Posts: 40
Joined: Sat Oct 20, 2018 3:13 pm
Location: Fort Worth, TX

Re: Upgrading to Super Z II - What do I need exactly?

Post by txtrone » Mon Sep 21, 2020 3:14 pm

davidwoods wrote:
Mon Sep 21, 2020 11:26 am
I am not for sure why you did not get your pp invoice, I am sorry(I can not see who you are on here). Did you end up getting another 12v wall plug, with the 12.6 IO? If your breakout board is UBOB, you will need a second one to power the FT-02 module. Please call me at CandCNC, if you did not.
Hey David, this is Morgan Wolfe. I think my order is going out this week. Do I need another 12v adapter?
Precision Plasma Magnum 7 HD on a five by ten
CommandCNC Linux
Hypertherm Powermax 85

When all else fails... read the directions.

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests